Plumbing Basics: The First Step for Bathtub Installation
Plumbing Basics: The First Step for Bathtub Installation
Blog Article
Just how do you feel in relation to Tools You Need to Install a New Bathtub ?
Setting up a bath tub isn't specifically brain surgery, however it does call for solid plumbing, carpentry, and also in some cases, tiling abilities. Replacing an old bathtub with a brand-new one is additionally a moderately hard job. If the old bathtub is easily obtainable, the job can relocate speedily; if you need to open a wall to eliminate the old tub as well as position the new tub, the task is a lot harder. In either situation, the project is within a home handyman's abilities, although you will need an assistant to leave the old bathtub and set in the new one. Make sure you have actually qualified on your own for the task and are comfortable attempting it. Rather than working with a professional to take over a halfway-completed project, it is far better to take into consideration using one before you start. Opportunities are you might require an expert plumber to make tube links.
This short article will certainly assist you mount a brand-new tub in your restroom if you have actually already bought a new tub as well as do not need to transform the arrangement of your previous water supply pipelines.
Your devices and also material list ought to comprise the following:
Planning for the Setup
Firstly, the sustaining frame supplied with the bath must be fitted (if needed) according to the producer's instructions. Next, fit the taps or mixer to the bathtub. When fitting the tap block, it is necessary to make certain that if the faucet features a plastic washer, it is fitted between the bathroom as well as the taps. On a plastic bathroom, it is also reasonable to fit a supporting plate under the faucets unit to stop pressure on the bath tub.
Fit the flexible faucet ports to the bottom of both faucets using 2 nuts as well as olives (occasionally provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet opening, and afterwards pass the outlet with the hole in the bathroom. Make use of the nut supplied by the producer to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next, fit completion of the flexible overflow pipeline to the overflow electrical outlet. After that, screw the pipeline to the overflow face which ought to be fitted inside the bathroom. See to it you make use of all of the provided washers.
Link the trap to the bottom of the waste outlet on the tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and screw on the trap to the outlet. Connect all-time low of the overflow tube in a comparable manner.The bath need to currently be ready to be suited its last position.
Removing Old Touches
If you need to change old taps with new ones as a part of your installment, then the first thing you need to do is detach the supply of water. After doing so, activate the taps to drain pipes any water continuing to be in the system. The process of eliminating the existing faucets can be quite troublesome as a result of the restricted gain access to that is frequently the situation.
Make use of a container wrench (crowsfoot spanner) or a faucet tool to undo the nut that attaches the supply pipes to the taps. Have a towel prepared for the staying water that will certainly come from the pipes. As soon as the supply pipelines have actually been gotten rid of, make use of the same tool to loosen up the nut that holds the faucets onto the bath/basin. You will require to quit the solitary taps from turning throughout this procedure. When the taps have been removed, the holes in the bath/basin will have to be cleaned of any old sealing compound.
Prior to going on to fit the brand-new taps, contrast the pipeline connections on the old faucets to the new faucets. If the old taps are longer than the brand-new taps, then a shank adapter is needed for the brand-new taps to fit.
Mounting the Tub
Using the two wood boards under its feet, put the bath tub in the required setting. The wood boards are useful in uniformly spreading the weight of the bath tub over the location of the boards rather than focusing all the weight onto 4 small factors.
The next goal is to ensure that the bath tub is leveled all round. This can be achieved by examining the level and readjusting the feet on the bathtub until the level checks out level.
To install taps, fit all-time low of the outermost versatile tap connector to the ideal supply pipeline by making a compression join; then do the very same for the other faucet.
Turn on the water system and examine all joints as well as new pipework for leaks and tighten them if needed. Fill the bath tub and likewise check the overflow outlet and also the normal electrical outlet for leakages.
Finally, fix the bathroom paneling as explained in the maker's user's manual. Tiling as well as sealing around the tub needs to wait up until the bathtub has been made use of at the very least when as this will resolve it into its final setting.
Fitting New Taps
If the tails of the brand-new taps are plastic, after that you will certainly require a plastic adapter to avoid damage to the thread. One end of the adapter fits on the plastic tail of the tap as well as the other end gives a connection to the current supply pipes.
If you need to fit a monobloc, then you will certainly need reducing couplers, which links the 10mm pipeline of the monobloc to the common 15mm supply pipeline.
Next, place the faucet in the mounting opening in the bath/basin making sure that the washers are in area in between the faucet as well as the sink. Safeguard the faucet in place with the producer offered backnut. Once the tap is safely in position, the supply pipes can be connected to the tails of the faucets. The faucets can either be connected by utilizing corrugated copper piping or with typical faucet connectors. The former kind should be connected to the tap finishes initially, tightening up only by hand. The supply pipes can later be connected to the other end. Tighten both ends with a spanner after both ends have actually been linked.
Tiling Around the Tub
In the location where the bathroom fulfills the tile, it is necessary to seal the joins with a silicone rubber caulking. This is essential as the fitting can move enough to crack an inflexible seal, creating the water to pass through the wall between the bathroom as well as the tiling, leading to issues with dampness and also feasible leakages to the ceiling listed below.
You can choose from a range of coloured sealants to blend in your fixtures and also installations. They are marketed in tubes as well as cartridges, and can sealing gaps approximately a size of 3mm (1/8 inch). If you have a bigger void to load, you can fill it with spins of drenched paper or soft rope. Keep in mind to always load the tub with water prior to sealing, to permit the motion experienced when the bathtub is in use. The sealant can split rather early if you do not take into consideration this movement before sealing.
Additionally, ceramic coving or quadrant ceramic tiles can be utilized to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and cut to size, are additionally easily available on the market. It is a good idea to fit the tiles making use of waterproof or water resistant adhesive and also cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
As an avid reader about How to Install a Bathtub, I imagined sharing that portion was worthwhile. Liked our article? Please share it. Help someone else locate it. Thank you for your time. Visit again soon.
See Availability Report this page